bannerbar

Support > Technical Support

Q&A

Your information is protected by SSL.

No. 1570	Re: Re: Re: Re: Re: at+pssl	2018-03-05

Dear Marc, Thank you for your information. Could you please let us know the return value of "at+pssl?" command, after when you active/deactivate SSL using AT command. For example, you may try sending AT commands as below and let us know the return message after each command: at+pssl=0[CR] at+pssl? [CR] at+pssl=1[CR] at+pssl?[CR] If it works normally, the response message should be like this: at+pssl=0[CR] OK at+pssl?[CR] 0 OK at+pssl=1[CR] OK at+pssl?[CR] 1 OK The "at+pwp" command should be used if you want to write the setting to ezTCP device, so that the setting will be saved even if you reboot the product. Thank you very much. Best Regards, > Marc wrote: > ------------------------------------ > When I execute the at+pwp command it returns OK, but after this I do not get any response anymore to any at-command. > > When I then power-down/power-up the device. it is working with the ssl setting active. > > > > > Sollae Systems wrote: > > ------------------------------------ > > Dear Marc, > > > > The command at+pwp should be used to save the setting to the device. > > After that, to check SSL status, you may use the command: at+pssl? > > In case there is still a problem, could you please let us know more clearly about the situation that those AT commands do not have any effect? > > > > Please feel free to contact us if you have any inquiry. > > > > Thank you for your understanding. > > Best Regards, > > > > > > > Marc wrote: > > > ------------------------------------ > > > HI, > > > > > > Thanks for the info. It is indeed the CSE-M53N that I have. I was able to upgrade to this new firmware. > > > > > > Unfortunately the at+pssl does not seem to work. I get OK when I execute the command, but it does not have any effect. > > > Is it a requirement to execute the at+pwp command afterwards. (I only want to change the ssl option temporary)? > > > > > > Regards, > > > Marc > > > > > > > > > > > > > Sollae Systems wrote: > > > > ------------------------------------ > > > > Dear Marc, > > > > > > > > This is Technical support team of Sollae Systems. > > > > > > > > Thank you for using our products. > > > > > > > > We would like to make sure that when you mention about CSE-M32N, are you referring to CSE-M32 or CSE-M53N? > > > > > > > > In case you refer to CSE-M32, there is NO beta firmware that supports AT command to activate or deactivate the SSL. > > > > > > > > In case you refer to CSE-M53N, you can get the beta firmware (similar to Q&A 1476) here http://cloud.eztcp.com/201802/CSE-M53N_R20B_07.BIN > > > > > > > > Since this is just a beta version, we have not tested it carefully and we cannot guarantee it works as the official firmware. > > > > > > > > - To check SSL status: at+pssl? > > > > - To activate SSL: at+pssl=1 > > > > - To deactivate SSL: at+pssl=0 > > > > - To save the setting, you need to send at+pwp command > > > > > > > > You can refer to the page 45 of User Manual to see how to upgrade the firmware. https://www.eztcp.com/en/download/pds_files/csem53nen.pdf > > > > > > > > For more information about AT Command, please refer to https://www.eztcp.com/en/download/pds_files/an_atc_mode_en.pdf > > > > > > > > Please feel free to contact us if you have any inquiry. > > > > > > > > Best regards, > > > > > > > > > > > > > Marc wrote: > > > > > ------------------------------------ > > > > > In Q&A 1476 is said that there exist beta firmware for CSE-M32N implementing the at+pssl at command. But it looks like the link is not available anymore. > > > > > How could I get this firmware? (I also need the available to switch ssl on and off with an at-command)

Writer	Sollae Systems	Company