bannerbar

Support > Technical Support

Q&A

Your information is protected by SSL.

No. 1601	Re: Re: Re: Re: Re: problem to have in status with cieh10	2018-10-18

Dear Jean Claude, As mentioned in page 18 of Modbus/TCP document, to get the DI ports status of CIE-H10, the Starting address should be the value of [Input Port Base Address]. It depends on the setting parameters of your CIE-H10. To get the current value of [Input Port Base Address] of your CIE-H10, you can: Connect ezManager to your CIE-H10 ==> I/O port ==> Basic Settings. Then you can find the value of [Input Port Base Address] in Modbus/TCP section. For your reference, by default, the value of [Input Port Base Address] is set to 0, so that the value of Starting address(2 bytes) is 00 00. And in that case, the request data will look like: 03 00 00 00 01 Could you please check your setting parameters and verify again? Thank you very much. Best Regards > Anonymous wrote: > ------------------------------------ > > thank you for your response > > i change my request 03 > > but now j find 11110000 allways > > when i push it s same. > > are you sure for the adress of registre ? > > > thank again > > Sollae Systems wrote: > > ------------------------------------ > > Dear Jean Claude, > > > > As you said, you send FC03 requests to get the DI status of CIE-H10. > > Refer to page 18 of Modbus/TCP document https://www.eztcp.com/en/download/pds_files/an_modbus_tcp_en.pdf, > > the request frame for FC03 should include: > > > > Function code (1byte) \| Starting address (2 bytes) \| Quantity of Register (2 bytes) > > > > So normally, the request data may look like: 03 00 08 00 01 > > > > We don't see this function code (0x03) in your request frame, so first please check your request data. > > You can use Wireshark to monitor your Modbus/TCP data. > > > > In case there is still a problem, we can establish a TeamViewer session. > > You can set up a schedule and send your credentials (ID and password) to us via email support@eztcp.com. > > Our working time is from 9:00 to 18:00 in UTC+9 Time zone. > > > > Thank you for your understanding. > > Best Regards > > > > > > > goldak wrote: > > > ------------------------------------ > > > hi > > > > > > i have tested of course the led of di0 is on > > > > > > i send a request 000006120008 > > > > > > i have a response > > > > > > 0 0 0 0 0 4 1 2 1 0 > > > > > > > > > the #9 is allways 0 > > > > > > > > > i have tried with fc04 request > > > > > > i have a response 4 but the digit #10 is allways 0 > > > > > > > > > if you want we can use teamwiever > > > > > > thank you to help me > > > > > > > Sollae Systems wrote: > > > > ------------------------------------ > > > > Dear Jean Claude, > > > > > > > > Please note that if the DI ports status is not changed, then the results should be the same. > > > > So for testing, you should manually change the input value of DI ports while making FC03 requests. > > > > > > > > In case the DI ports status is changed and CIE-H10's responses are still the same, could you please let us know more detail how did you send FC03 requests. > > > > For further analysis, please also provide us the Wireshark log while you are making FC03 requests. > > > > > > > > Thank you very much. > > > > Best Regards > > > > > > > > > > > > > goldak wrote: > > > > > ------------------------------------ > > > > > hi > > > > > > > > > > i am back from holydays > > > > > > > > > > thank you for the documentation of modbus > > > > > > > > > > i make some request (fc03) to have the in status > > > > > > > > > > the cieh10 send me allway the same > > > > > > > > > > please help me > > > > > > > > > > the version is 2.0 rev A > > > > > > > > > > thank you jean claude

Writer	Sollae Systems	Company