FAQ

Category : basic
Category : how to

ISP (In System Programming) mode

ISP mode is used as download firmware to ezTCP through the Ethernet(TFTP) - except EZL-200F
- Warning
When ezTCP runs in ISP mode, the data communication function does not work.
Reset the ezTCP after operation in ISP mode

- You can enter ISP mode for each product as follows:

EZL-50 / 50L	Reset or power on EZL-50 / 50L after pulling down ISP- pin. In case EZL-EVB, reset or power on EZL-EVB after locating JP3 on ISP- side. During ISP mode, the [STS LED] will be blinking rapidly. [Detail view - product only] [Detail view - withEZL-EVB]
EZL-60 / 60L	Reset or power on EZL-60 / 60L after locating JP1 on ISP- side. During ISP mode, the [STS LED] will be blinking rapidly. [Detail view]
EZL-70	Reset or power on EZL-70 with setting ISP jumper(JP1). During ISP mode, the [STS LED] will be blinking rapidly.
EZL-200L	Power on EZL-200L with pressing the ISP button beside the RJ-45 jack. During ISP mode, the [STS LED] will be blinking rapidly.
EZL-200F	Power on EZL-200F with pressing the ISP button beside the RJ-45 jack. During ISP mode, the [STS LED] will be ON.
EZL-410	Reset or power on EZL-410 after pulling down ISP(JP1 #4) pin. In case EZL-EVB, you can enter ISP mode by locating JP5 on ISP side.
EZL-300S / 400S	There is no ISP mode. They can download the firmware after telnet login.
CSE-M32	Reset or pwer on CSE-M32 after pulling down ISP- pin. In case of using EVB, connect the JP5 to ISP- section.
CSE-H20 / H21 / H25 / H53 / H55 / CIE-H10 / CSW-H80	Reset or supply power with pressing ISP button. Or press the button over 3 seconds.
CIE-M10	Reset or supply power after pulling down ISP- pin.
CSE-M73	Reset or supply power after connecting JP6. Or keep the place of JP6 over 3 seconds.
CSE-M53	Reset or power on EZL-50 / 50L after pulling down ISP- pin. In case of using EVB, reset or supply power after connecting JP7.
CSW-M83 / M85	Reset or power on CSW-M83 / M85 after pulling down ISP-(JP1 #3) pin over 3 seconds.
CSP-H50	Reset or supply power with pressing ISP button. Or input "pf" command in command mode.
Other ezTCP/Wireless product line	when reset or power on ezTCP/W-LAN product without any W-LAN card, if there is no < CR > about 2 seconds, ezTCP/W-LAN product operates as Console mode. Otherwise it operates as ISP mode.

Console mode

In console mode, you can configure the environmental parameters of ezTCP via serial port.
And [ezConfig] and [Telnet] functions are enabled, regardless of configuration.
- Warning

In console mode, all security functions are disabled.
If you have lost your password, you can remove or change the password in this mode.
And the data communication function does not work. Reset the ezTCP after operation in console mode.

- You can enter Console mode for each product as follows:

EZL-200F / 220	Press and hold the ISP button beside the RJ-45 jack for one second. During Console mode, the [STS LED] will be blinking rapidly.
EZL-400S	Press a [CONSOLE S/W] which is located the front side of ethEZL-400S over 1 second. During Console mode, [RUN LED] and [STS1 LED] blink at the same time.
Other ezTCP/Wireless product line	when reset or power on ezTCP/W-LAN product without any W-LAN card, if there is no < CR > about 2 seconds,ezTCP/W-LAN product operates as console mode.
Other ezTCP/Ethernet product line	There is no console mode for these products

---

See also


Related Products

[ Ethernet-Module ] CSE-M53, CSE-M32, EZL-50L, EZL-50M, EZL-410
[ Ethernet-Module with RJ45 ] CSE-M73, EZL-70,
[ Ethernet-Board ] EZL-60L, EZL-60M, CSE-B63
[ Ethernet-External ] CSE-H55, CSE-H53, CSE-H25, CSE-H20, CSE-H21, EZL-200L, EZL-200F, EZL-400S
[ Wireless-External ] EZL-300S, CSW-H80
[ Wireless-Module ] CSW-M83
[ PPP ] EZP-250, EZU-100, CSP-H50, EZP-EVB, EZU-EVB
[ I/O ] EZI-10, CIE-H10, CIE-M10